sensor
-
G
idle problem
when the car starts from cold it almost stalls (the idle jumps up and down from 300 to 600 rpm) after about 20 seconds it returns to normal cold start. once temp guage reads middle, the car idles massive lumpy cam style as i have NO cams this is not good!( jumps from 800 down to 600 almost...- GUEST_JDM
- Thread
- Replies: 10
- Forum: Mechanical & Bodywork
-
F
Exhaust Questions
Ok I’m building an exhaust for my S15 SpecR and my questions are What is the best diameter to use? Is there meant to be a sensor near the cat mine has been removed and there is no sign of a sensor? And is the dump pipe, down pipe and cat replacement pipe the same as the S14? Many thanks in...- freebird
- Thread
- Replies: 1
- Forum: Mechanical & Bodywork
-
e-manage ultimate question
hi guys, does anybody knows if you can remove completely the maf sensor if you install the e-manage pressure sensor?- koullis
- Thread
- Replies: 8
- Forum: Electrical & Audio
-
ABS Light On
Have just finished work,got in my car and the ABS light is now staying on,has anyone had this problem and any ideas as to the cure? The rear pads are very low not sure about the fronts though will the low pad sensor light this up or is that a seperate warning lamp.Actually does anyone know all...- S15RKM
- Thread
- Replies: 12
- Forum: Electrical & Audio
-
S
Fitting Lambda / Oxygen Sensor
Guys Just thought id let you know that I managed to change the sensor today in just 20mins with a special socket I bought. I got it from a local motor shop but you can also buy it from here. http://www.motorshack.com/acatalog/Special_Sockets.html SLOTTED SOCKET 3/8" DRIVE - OXYGEN SENSOR 22...- shadyuk
- Thread
- Replies: 4
- Forum: Mechanical & Bodywork
-
Water Temp sensor adapter thingy!!
Hey guys am for fitting a defi water temp sensor and was wondering if its better to fit the adapter thingon the top or bottom hose?Also do u know what size that hose is?40 mm poss?- Robbyp
- Thread
- Replies: 1
- Forum: Mechanical & Bodywork
-
P
lambda sensor
where could I get one of these from, I think mine is dead!!! help plz in sourcing one :)- PhilV
- Thread
- Replies: 2
- Forum: Mechanical & Bodywork
-
JDM Boost sensor...
Well i say JDM as the AUS service manual doesnt show its existence!!!! On fast car its listed as a boost sensor... and from what i gather the ADM S15 dont come with factory boost guages?!?! So... Would i be right in guessin that this sensor is used purely for the JDM OEM boost gauge???- channie
- Thread
- Replies: 2
- Forum: Mechanical & Bodywork
-
S
POWER FC Djetro
guys... anyone out there using powerFC djetro version(map sensor version)?? i have a question here. does anyone know which wire to tap for the air temp sensor? i got the powerFC manual with me..but it is in japanese. basically there is two wires that need to be tap, i know which pin i should...- silvialam
- Thread
- Replies: 0
- Forum: Mechanical & Bodywork
-
E
I think I'm cursed never to get my car running again :( :(
Another less than positive experience today with the car. I was all ready to do the Auto to Manual swap today after the auto box gave up the ghost last month. I had all the parts I thought I needed fresh from Perfectrun and was all set. I'd agreed to purchase the MT a while back from Albert -... -
Door light sensor not working
Just noticed that my interior light isn't coming on when I open the passenger door. Had a look in the pressure sensor and found only one wire going to the connector. Not really an issue, as the screw would earth the sensor. Checked the driver's door and there are three or four wires. Swapped...- Nicely
- Thread
- Replies: 6
- Forum: Electrical & Audio
-
A
About OIL Press sensor...
I have greddy gauge OIL press w/o sensor. So but I have defi sensor from Oil press gauge. Will it work with greddy gauge???- Albert
- Thread
- Replies: 0
- Forum: Electrical & Audio
-
lambda nut
What nut do I need for the lamda in the downpipe? I think the S13 has M18 by 1.5 pitch nut. Is the S14/15 the same? Also in FAST there seems to be an adapter on the lambda sensor :confused:- Yakozan
- Thread
- Replies: 13
- Forum: Mechanical & Bodywork